Wood-mizer 1992 LT40HD Operator's Manual download pdf (Page 136)

Sawmill Alignment

Saw Head Tilt

5-26 HD92doc042701 Sawmill Alignment

5.19 Saw Head Tilt

As the blade enters a wide log or cant, the outside of the saw head will drop down slightly.

To compensate for the drop, use the lower track roller horizontal bolts to raise the outside

of the saw head 1/16".

1. Move the saw head so the blade is positioned 14 3/4" (375 mm) above a bed rail.

2. Adjust the lower track roller horizontal bolts until the blade measures 14 13/16"

(376.5 mm) from the bed rail near the outer blade guide.

See Figure 5-20.

FIG. 5-20

1 2 ... 131 132 133 134 135 136 137 138 139 140

Wood-Mizer 1
IfYouNeedToOrderParts 2
1-800-448-7881 2
IfYouNeedService 3
1-800-525-8100 3
Customer Number 4
V.I.N. DESCRIPTION 5
MODEL NUMBER DESCRIPTION 5
1.1 Blade Handling 11
1.2 Sawmill Setup 11
1.3 Sawmill Operation 12
Sawmill Operation 13
1.4 Belt Sizes 14
1.5 Blade Sizes 15
1.6 Cutting Capacity 16
Engine/Motor Specifications 17
1.8 Overall Dimensions 18
1.9 Components 19
1.10 Hydraulic Schematic 20
Hydraulic Schematic 21
1.11 Hydraulic Components 22
Hydraulic Components 23
1.12 Hydraulic Hoses 24
Hydraulic Hoses 25
Setup & Operation 29
2.1 Stationary Sawmill Setup 29
2.2 Portable Sawmill Setup 30
Bed Rail 32
Stop Block 32
Pivot End Rail 32
Side Support 32
2.4 Replacing The Blade 34
2.5 Tensioning The Blade 35
2.6 Tracking The Blade 36
2.10 Clamp Extension 46
2.11 Up/Down Operation 47
2.13 Clutch/Brake Operation 49
2.14 Power Feed Operation 50
2.15 Cutting The Log 52
2.16 Edging 53
2.17 Blade Height Sight Gauge 54
2.18 Blade Height Scale 55
2.19 Water Lube Operation 58
SECTION 3 MAINTENANCE 63
Maintenance 64
3.2 Blade Guides 64
3.3 Hydraulic Log Loader 65
3.4 Blade Housing 66
3.6 Track Rollers 68
3.7 Vertical Mast Rails 69
3.8 Drum Switches 70
3.9 Miscellaneous Lubrication 71
3.10 Blade Tensioner 72
3.11 Blade Wheel Belts 73
3.12 Brake Strap Adjustment 74
3.13 Hydraulic System 76
3.14 Drive Bearing 78
3.15 Up/Down System 79
3.16 Power Feed 82
4.1 Sawing Problems 93
4.2 Electrical Problems 95
4.3 Power Feed Problems 97
Troubleshooting Guide 100
4.5 Hydraulic Problems 101
4.10 Hydraulic Pressure Test 108
SECTION 5 SAWMILL ALIGNMENT 111
Sawmill Alignment 112
5.2 Frame Setup 112
5.9 Aligning The Blade Guides 124
5.10 Blade Deflection 125
5.12 Blade Guide Spacing 128
5.16 Clamp Stop Adjustment 132
5.18 Sight Gauge Adjustment 135
5.19 Saw Head Tilt 136

Comments to this Manuals

No comments

Wood-mizer 1992 LT40HD Operator's Manual Page 136

Comments to this Manuals